GC Gold Label 2 Lc (Light-Cured)

• Class III and V restorations, particularly for cervical erosions and root surface caries
• Restoration of primary teeth
• Core build up
• Cases where radiopacity is required
• Geriatric applications
• As a base or liner.

CONTRAINDICATIONS

• Pulp capping
• In rare cases the product may cause sensitivity in some people. If any such reactions are experienced, discontinue the use of the product and refer to a physician

ADVANTAGES:

• Allows minimal cavity preparation
• Less stress on margins and marginal seal
• Protects against secondary caries
• Excellent esthetics and finish
• Improved abrasion resistance
• Allows for immediate finishing after light curing while ensuring total material set
• Ease of colour match to tooth shade
• More durable, longer lasting restorations
• Assurance of successful restorations

Features: 

• Smaller particles
• Excellent aesthetics and polishability
• Higher filler loading
• Significantly improved abrasion resistance
• Good radiopacity
• Facilitating post-operative diagnosis
• Self-adhesive to tooth structure
• No etching, no bonding
• Hydrophilic
• Very good results in areas where rubber dam is difficult to use, cavity margins are in dentin and enamel prisms can not be properly etched
• Smooth, porosity-free surface after sealing with GC G-Coat Plus
• Practical application and manipulation
• Excellent aesthetics

Key Specifications: 

TECHNICAL DATA:

• Powder / Liquid Ratio (g/g):3.2 / 1.0
• Mixing Time (sec.):20-25 secs
• Working Time (min., sec.): 3 mins45 secs
• Light Curing Time (sec.):20 secs
• Depth of Cure (A2) (mm):1.8

Packaging: 

Gc Gold Label 2 Lc Mini Pack Shade A2:

• 1 x 5g Powder
• 1 x 3g (2.6ml) Liquid

Gc Gold Label 2 Lc 1-1 Pkg Shade A2:

• 1 x 15g Powder
• 1 x 8g Liquid

Direction To Use: 

1. POWDER AND LIQUID DISPENSING

a) Select shade based on Vita shade guide.  : Vita is a registered trademark of Vita Zahnfabrik, Bad Säckingen, Germany

b) The standard powder to liquid ratio is 3.2g / 1.0g. 1 level scoop of powder to 2 drops of liquid

c) For accurate dispensing of powder, tap the bottle gently. Do not shake or invert

d) Hold the liquid bottle vertically and squeeze gently

e) Close bottles immediately after use

2. MIXING

a) Fluff powder of bottle before dispensing

b) Place one scoop of powder and two drops of liquid on pad. Divide powder in half

c) Spread liquid out into a thin layer (about the size of a half dollar or 3 cm) with plastic spatula

d) Pull half of the powder onto liquid and mix with lapping strokes (like impression material) for 10 to 15 seconds

e) Pull in remaining powder and mix thoroughly to a glossy consistency. Do not exceed 20-25 second total mixing time

3. RESTORATIVE TECHNIQUE

a) Prepare tooth using standard techniques. Extensive mechanical retention is not necessary. For pulp capping use calcium hydroxide

b) Apply GC CAVITY CONDITIONER (10 seconds) or GC DENTIN CONDITIONER (20 seconds) to the bonding surfaces using a cotton pellet or sponge

c) Rinse thoroughly with water. Dry by blotting with a cotton pellet or gently blowing with an air syringe. DO NOT DESICCATE. Best results are obtained when prepared surfaces appear moist (glistening)

d) Mix the required amount of cement. Working time is 3 minutes 45 seconds from the start of mixing at 23°C (73.4°F). Higher temperatures will shorten working time

e) Transfer cement to the preparation using a syringe or suitable placement instrument. Avoid air bubbles

f) Form the contour and place a transparent matrix if required

g) Light cure for 20 seconds using a visible light curing device (470 nm wavelength). Place light source as closely as possible to the cement surface. Note : For cavities deeper than 1.8 mm, use a layering technique

4. FINISHING

Remove matrix and finish under water spray using standard techniques. Note : Apply a final coat of GC Fuji VARNISH (blow dry) or GC Fuji COAT LC (light cure for 10 sec.) or G-COAT PLUS (light cure for 20 sec.).